HomeMy WebLinkAboutLiquid-Wrench-Super-Penetrant-Gunk-RCS-Chemical-Solutions-10-4-17SAFETY DATA SHEET
1. Identification
Liquid Wrench Penetrating OilProduct identifier
Other means of identification
L112SDS number
L106, L112Part No.
3403.19.5000Tariff code
Penetrating OilRecommended use
None known.Recommended restrictions
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
RSC Chemical Solutions
Address 600 Radiator Road
Company name
Website
Telephone Customer Service: (704) 821-7643
Technical: (704) 684-1811
Emergency phone number Emergency Telephone: (303) 623-5716
Emergency Contact: RMPDC (877) 740-5015
E-mail
United States
www.rscbrands.com
sds@rscbrands.com
Indian Trail, NC 28079
2. Hazard(s) identification
Category 2Flammable aerosolsPhysical hazards
Category 4Acute toxicity, oralHealth hazards
Category 2Skin corrosion/irritation
Category 2ASerious eye damage/eye irritation
Category 1BSensitization, skin
Category 3 narcotic effectsSpecific target organ toxicity, single exposure
Category 1Aspiration hazard
Category 2Hazardous to the aquatic environment, acute
hazard
Environmental hazards
Category 2Hazardous to the aquatic environment,
long-term hazard
Not classified.OSHA defined hazards
Label elements
Signal word Danger
Hazard statement Flammable aerosol. Contains gas under pressure; may explode if heated. Harmful if swallowed.
May be fatal if swallowed and enters airways. Causes skin irritation. May cause an allergic skin
reaction. Causes serious eye irritation. May cause drowsiness or dizziness. Toxic to aquatic life
with long lasting effects.
1 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. No smoking. Do not spray on an open
flame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Avoid
breathing mist or vapor. Wash thoroughly after handling. Do not eat, drink or smoke when using
this product. Use only outdoors or in a well-ventilated area. Contaminated work clothing must not
be allowed out of the workplace. Avoid release to the environment. Wear eye protection/face
protection. Wear protective gloves.
Response IF SWALLOWED: Immediately call a POISON CENTER/doctor. IF IN EYES: Rinse cautiously
with water for several minutes. Remove contact lenses, if present and easy to do. Continue
rinsing. Rinse mouth. Do NOT induce vomiting. If on skin: Wash with plenty of water. IF INHALED:
Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse cautiously with
water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
Call a poison center/doctor if you feel unwell. If skin irritation or rash occurs: Get medical
advice/attention. If eye irritation persists: Get medical advice/attention. Take off contaminated
clothing and wash it before reuse. Collect spillage.
Storage Store in a well-ventilated place. Keep container tightly closed. Store locked up. Protect from
sunlight. Do not expose to temperatures exceeding 50°C/122°F.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise
classified (HNOC)
Combustible.
Supplemental information 97.91% of the mixture consists of component(s) of unknown acute dermal toxicity. 95.11% of the
mixture consists of component(s) of unknown acute inhalation toxicity.
NOTE: This product is a consumer product and is labeled in accordance with the US Consumer
Product Safety Commission regulations which take precedence over OSHA Hazard
Communication labeling. The container label may not include the OSHA label elements listed in
this document. Always carefully review the entire SDS and the product label prior to use in the
workplace.
3. Composition/information on ingredients
Mixtures
CAS number %Chemical name Common name and synonyms
64742-47-8Distillates (petroleum),
Hydrotreated Light
70 - < 80
1581740-29-51,6,10-dodecatriene,
7,11-dimethyl-3-methylene-, (6e)-,
Hydrogenated
5 - < 10
10 - < 20Other components below reportable levels
124-38-9Carbon Dioxide 1 - < 3
*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.
4. First-aid measures
Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a POISON
CENTER or doctor/physician if you feel unwell.
Inhalation
Remove contaminated clothing immediately and wash skin with soap and water. In case of
eczema or other skin disorders: Seek medical attention and take along these instructions. Wash
contaminated clothing before reuse.
Skin contact
Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if
present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.
Eye contact
Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If
vomiting occurs, keep head low so that stomach content doesn't get into the lungs.
Ingestion
Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.
Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,
redness, swelling, and blurred vision. Skin irritation. May cause redness and pain. May cause an
allergic skin reaction. Dermatitis. Rash.
Most important
symptoms/effects, acute and
delayed
Provide general supportive measures and treat symptomatically. Keep victim warm. Keep victim
under observation. Symptoms may be delayed.
Indication of immediate
medical attention and special
treatment needed
Ensure that medical personnel are aware of the material(s) involved, and take precautions to
protect themselves. Show this safety data sheet to the doctor in attendance. Wash contaminated
clothing before reuse.
General information
2 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
5. Fire-fighting measures
Alcohol resistant foam. Powder. Dry chemicals. Carbon dioxide (CO2).Suitable extinguishing media
Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing
media
Contents under pressure. Pressurized container may explode when exposed to heat or flame.
During fire, gases hazardous to health may be formed.
Specific hazards arising from
the chemical
Firefighters must use standard protective equipment including flame retardant coat, helmet with
face shield, gloves, rubber boots, and in enclosed spaces, SCBA.
Special protective equipment
and precautions for firefighters
Move containers from fire area if you can do so without risk. Cool containers exposed to heat with
water spray and remove container, if no risk is involved. Containers should be cooled with water to
prevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder or
monitor nozzles, if possible. If not, withdraw and let fire burn out.
Fire fighting
equipment/instructions
Use standard firefighting procedures and consider the hazards of other involved materials. Move
containers from fire area if you can do so without risk. In the event of fire and/or explosion do not
breathe fumes.
Specific methods
Flammable aerosol. Contents under pressure. Pressurized container may explode when exposed
to heat or flame. Combustible.
General fire hazards
6. Accidental release measures
Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wear
appropriate protective equipment and clothing during clean-up. Avoid breathing mist or vapor. Do
not touch damaged containers or spilled material unless wearing appropriate protective clothing.
Ventilate closed spaces before entering them. Local authorities should be advised if significant
spillages cannot be contained. For personal protection, see section 8 of the SDS.
Personal precautions,
protective equipment and
emergency procedures
Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so without
risk. Move the cylinder to a safe and open area if the leak is irreparable. Use water spray to reduce
vapors or divert vapor cloud drift. Keep combustibles (wood, paper, oil, etc.) away from spilled
material. Prevent product from entering drains. Absorb in vermiculite, dry sand or earth and place
into containers. Following product recovery, flush area with water.
Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to
remove residual contamination. For waste disposal, see section 13 of the SDS.
Methods and materials for
containment and cleaning up
Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all
environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into
drains, water courses or onto the ground.
Environmental precautions
7. Handling and storage
Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing
or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke
while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or
expose containers to heat, flame, sparks, or other sources of ignition. All equipment used when
handling the product must be grounded. Do not re-use empty containers. Do not taste or swallow.
Avoid breathing mist or vapor. Avoid contact with eyes, skin, and clothing. Avoid prolonged or
repeated contact with skin. Avoid prolonged exposure. When using, do not eat, drink or smoke.
Use only in well-ventilated areas. Wear appropriate personal protective equipment. Wash hands
thoroughly after handling. Avoid release to the environment. Observe good industrial hygiene
practices.
Precautions for safe handling
Level 3 Aerosol.
Store locked up. Pressurized container. Protect from sunlight and do not expose to temperatures
exceeding 50°C/122 °F. Do not puncture, incinerate or crush. Do not handle or store near an open
flame, heat or other sources of ignition. This material can accumulate static charge which may
cause spark and become an ignition source. Keep out of the reach of children. Store away from
incompatible materials (see Section 10 of the SDS).
Conditions for safe storage,
including any incompatibilities
8. Exposure controls/personal protection
Occupational exposure limits
The following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.
At this time, the other constituents have no known exposure limits.
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents Type
PEL 9000 mg/m3Carbon Dioxide (CAS
124-38-9)
3 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000)
ValueComponents Type
5000 ppm
PEL 400 mg/m3Distillates (petroleum),
Hydrotreated Light (CAS
64742-47-8)
100 ppm
US. ACGIH Threshold Limit Values
ValueComponents Type
STEL 30000 ppmCarbon Dioxide (CAS
124-38-9)
TWA 5000 ppm
US. NIOSH: Pocket Guide to Chemical Hazards
ValueComponents Type
STEL 54000 mg/m3Carbon Dioxide (CAS
124-38-9)
30000 ppm
TWA 9000 mg/m3
5000 ppm
No biological exposure limits noted for the ingredient(s).Biological limit values
Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates
should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,
or other engineering controls to maintain airborne levels below recommended exposure limits. If
exposure limits have not been established, maintain airborne levels to an acceptable level. Provide
eyewash station. Eye wash fountain and emergency showers are recommended.
Appropriate engineering
controls
Individual protection measures, such as personal protective equipment
Face shield is recommended. Wear safety glasses with side shields (or goggles).Eye/face protection
Skin protection
Wear appropriate chemical resistant gloves.Hand protection
Wear appropriate chemical resistant clothing.Other
If permissible levels are exceeded use NIOSH mechanical filter / organic vapor cartridge or an
air-supplied respirator. Chemical respirator with organic vapor cartridge and full facepiece if
threshold limits are exceeded. Dust & vapor respirator.
Respiratory protection
Wear appropriate thermal protective clothing, when necessary.Thermal hazards
When using do not smoke. Keep away from food and drink. Always observe good personal
hygiene measures, such as washing after handling the material and before eating, drinking, and/or
smoking. Routinely wash work clothing and protective equipment to remove contaminants.
Contaminated work clothing should not be allowed out of the workplace.
General hygiene
considerations
9. Physical and chemical properties
Liquid OpaqueAppearance
Liquid.Physical state
Aerosol.Form
YellowColor
FragranceOdor
Odor threshold Not available.
pH Not available.
Melting point/freezing point Not available.
Initial boiling point and boiling
range
469.04 °F (242.8 °C) estimated
Flash point 200.0 °F (93.3 °C) Tag Closed Cup
Evaporation rate Not available.
Not applicable.Flammability (solid, gas)
4 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
Upper/lower flammability or explosive limits
Flammability limit - lower
(%)
0.7 % estimated
Flammability limit - upper
(%)
8.5 % estimated
Explosive limit - lower (%)Not available.
Explosive limit - upper (%)Not available.
Vapor pressure 0.51 hPa estimated
Vapor density Not available.
Relative density Not available.
Solubility(ies)
Solubility (water)Not available.
Partition coefficient
(n-octanol/water)
Not available.
Auto-ignition temperature 530.6 °F (277 °C) estimated
Decomposition temperature Not available.
Viscosity Not available.
Other information
Density 7.26 lbs/gal
Not explosive.Explosive properties
Flame extension > 18 in
Flammability (flash back)No
Flammability class Combustible IIIB estimated
Heat of combustion (NFPA
30B)
36.35 kJ/g
Not oxidizing.Oxidizing properties
Percent volatile 0.29 % estimated
Specific gravity 0.87
VOC 0 %
10. Stability and reactivity
The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity
Material is stable under normal conditions.Chemical stability
No dangerous reaction known under conditions of normal use.Possibility of hazardous
reactions
Avoid temperatures exceeding the flash point. Contact with incompatible materials.Conditions to avoid
Strong oxidizing agents.Incompatible materials
No hazardous decomposition products are known.Hazardous decomposition
products
11. Toxicological information
Information on likely routes of exposure
Inhalation May cause drowsiness and dizziness. Headache. Nausea, vomiting. Prolonged inhalation may be
harmful.
Skin contact Causes skin irritation. May cause an allergic skin reaction.
Eye contact Causes serious eye irritation.
Ingestion Harmful if swallowed. Droplets of the product aspirated into the lungs through ingestion or
vomiting may cause a serious chemical pneumonia.
Symptoms related to the
physical, chemical and
toxicological characteristics
Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.
Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,
redness, swelling, and blurred vision. Skin irritation. May cause redness and pain. May cause an
allergic skin reaction. Dermatitis. Rash.
Information on toxicological effects
Acute toxicity May be fatal if swallowed and enters airways.
5 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
Causes skin irritation.Skin corrosion/irritation
Causes serious eye irritation.Serious eye damage/eye
irritation
Respiratory or skin sensitization
Respiratory sensitization Not a respiratory sensitizer.
May cause an allergic skin reaction.Skin sensitization
No data available to indicate product or any components present at greater than 0.1% are
mutagenic or genotoxic.
Germ cell mutagenicity
Carcinogenicity Not classifiable as to carcinogenicity to humans.
IARC Monographs. Overall Evaluation of Carcinogenicity
Not listed.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not regulated.
US. National Toxicology Program (NTP) Report on Carcinogens
Not listed.
This product is not expected to cause reproductive or developmental effects.Reproductive toxicity
Specific target organ toxicity -
single exposure
May cause drowsiness and dizziness.
Specific target organ toxicity -
repeated exposure
Not classified.
Aspiration hazard May be fatal if swallowed and enters airways.
Chronic effects Prolonged inhalation may be harmful.
12. Ecological information
Toxic to aquatic life with long lasting effects.Ecotoxicity
Components Test ResultsSpecies
Distillates (petroleum), Hydrotreated Light (CAS 64742-47-8)
Aquatic
EC50Crustacea 2.7 - 5.1 mg/l, 48 hoursWater flea (Daphnia pulex)
* Estimates for product may be based on additional component data not shown.
LC50Fish 2.9 mg/l, 96 hoursRainbow trout,donaldson trout
(Oncorhynchus mykiss)
Persistence and degradability
Bioaccumulative potential
Partition coefficient n-octanol / water (log Kow)
1,6,10-dodecatriene, 7,11-dimethyl-3-methylene-, (6e)-,
Hydrogenated
6.08 - 6.48 OECD 117, Log Kow
No data available.Mobility in soil
Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation
potential, endocrine disruption, global warming potential) are expected from this component.
13. Disposal considerations
Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Contents
under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into
sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used
container. Dispose of contents/container in accordance with local/regional/national/international
regulations.
Disposal instructions
Dispose in accordance with all applicable regulations.Local disposal regulations
The waste code should be assigned in discussion between the user, the producer and the waste
disposal company.
Hazardous waste code
Dispose of in accordance with local regulations. Empty containers or liners may retain some
product residues. This material and its container must be disposed of in a safe manner (see:
Disposal instructions).
Waste from residues / unused
products
Since emptied containers may retain product residue, follow label warnings even after container is
emptied. Empty containers should be taken to an approved waste handling site for recycling or
disposal. Do not re-use empty containers.
Contaminated packaging
6 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
14. Transport information
DOT
Not available.UN number
Consumer CommodityUN proper shipping name
ORM-DClass
Transport hazard class(es)
-Subsidiary risk
Not available.Packing group
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
306Packaging exceptions
NonePackaging non bulk
NonePackaging bulk
IATA
UN1950UN number
Aerosols, flammableUN proper shipping name
2.1Class
Transport hazard class(es)
-Subsidiary risk
Not available.Packing group
YesEnvironmental hazards
10LERG Code
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
Allowed with restrictions.Passenger and cargo
aircraft
Other information
Allowed with restrictions.Cargo aircraft only
IMDG
UN1950UN number
Aerosols, flammable, MARINE POLLUTANTUN proper shipping name
2.1Class
Transport hazard class(es)
-Subsidiary risk
Not available.Packing group
YesMarine pollutant
Environmental hazards
F-D, S-UEmS
Read safety instructions, SDS and emergency procedures before handling.Special precautions for user
Not established.Transport in bulk according to
Annex II of MARPOL 73/78 and
the IBC Code
IATA; IMDG
7 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
Marine pollutant
IMDG Regulated Marine Pollutant.General information
15. Regulatory information
This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication
Standard, 29 CFR 1910.1200.
US federal regulations
TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)
Not regulated.
CERCLA Hazardous Substance List (40 CFR 302.4)
Not listed.
SARA 304 Emergency release notification
Not regulated.
OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050)
Not regulated.
Superfund Amendments and Reauthorization Act of 1986 (SARA)
Immediate Hazard - Yes
Delayed Hazard - No
Fire Hazard - Yes
Pressure Hazard - No
Reactivity Hazard - No
Hazard categories
SARA 302 Extremely hazardous substance
Not listed.
NoSARA 311/312 Hazardous
chemical
SARA 313 (TRI reporting)
Not regulated.
Other federal regulations
Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List
Not regulated.
Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)
Not regulated.
Not regulated.Safe Drinking Water Act
(SDWA)
California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material
is not known to contain any chemicals currently listed as carcinogens or reproductive toxins.
US state regulations
International Inventories
Country(s) or region Inventory name On inventory (yes/no)*
NoAustralia Australian Inventory of Chemical Substances (AICS)
NoCanada Domestic Substances List (DSL)
YesCanada Non-Domestic Substances List (NDSL)
NoChina Inventory of Existing Chemical Substances in China (IECSC)
NoEurope European Inventory of Existing Commercial Chemical
Substances (EINECS)
NoEurope European List of Notified Chemical Substances (ELINCS)
NoJapan Inventory of Existing and New Chemical Substances (ENCS)
NoKorea Existing Chemicals List (ECL)
NoNew Zealand New Zealand Inventory
8 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US
Country(s) or region Inventory name On inventory (yes/no)*
NoPhilippines Philippine Inventory of Chemicals and Chemical Substances
(PICCS)
YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory
*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)
A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing
country(s).
16. Other information, including date of preparation or last revision
04-27-2015Issue date
10-04-2017Revision date
Version #09
Health: 2
Flammability: 1
Physical hazard: 0
HMIS® ratings
Health: 2
Flammability: 1
Instability: 0
NFPA ratings
NFPA ratings
02
1
The information provided in this Safety Data Sheet is correct to the best of our knowledge,
information and belief at the date of its publication. The information given is designed only as a
guidance for safe handling, use, processing, storage, transportation, disposal and release and is
not to be considered a warranty or quality specification. The information relates only to the specific
material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
Disclaimer
This document has undergone significant changes and should be reviewed in its entirety.Revision information
9 / 9
Material name: Liquid Wrench Penetrating Oil
L106, L112 Version #: 09 Revision date: 10-04-2017 Issue date: 04-27-2015
SDS US